1.2mmAPF-3000 pressure-sensitive adhesive polymer waterproofing membrane reactive one, 1.2mmAPF-3000 pressure-sensitive adhesive reactive polymer waterproofing membrane Features ● good mechanical properties, can effectively guarantee the material to resist wind loads. ● has good low temperature flexibility and high temperature stability, the impact of which is not temperature changes. ● Good anti-perforation and impact resistance. ● acid and other chemical resistance is good. ● has a very good thermoplastic lap using professional hot air welding, can effectively ensure the seams watertight. ● professional design and excellent detail node processing. ● 1.2mmAPF-3000 has a sensitive reaction waterproof membrane performance characteristics TPO membrane, while the self-adhesive layer is soft and good extension, can better adapt to the grassroots deformation. 2. Introduction Figure II, the scope for industrial, civil construction roofing and underground works. -H Waterproofing membrane is mainly used for roofing; waterproofing membrane -L type is mainly applied to high bridge, underground works; waterproofing membrane -P mainly used for roofing grass or wood and other metal plate; waterproofing membrane -SA type is mainly used in green roofs, underground engineering. Three, 1.2mmAPF-3000 pressure-sensitive adhesive reactive waterproofing design features a single-layer waterproofing membrane roofing projects 1) Single waterproofing membrane roofing should be the existing national standard "building structural load specifications" GB 50009 of the relevant provisions of the wind load calculations. 2) slope roof project should be greater than 1%. Press the top method using empty shop roof construction, the slope should not exceed 10%. 3) should have compatibility between the waterproofing material used in roofing works with grassroots and insulation materials with each other. When the waterproof layer is incompatible with the adjacent material shall be added to the shop and waterproof layer of insulating material compatibility. Using the back cover of the nonwoven fabric waterproofing membrane may increase the insulating material shop. 4) should be set up between the single-ply membrane roofing and waterproofing membrane voltage protective layer; when the grass is hard and relatively coarse, should increase shop soft cushioning material, cushioning material with waterproof layer should be compatible. When the grass is soft and incompatible with waterproof layer, waterproof layer should be laid by laying a soft insulating material, the insulating material should be compatible with the waterproof layer. 5) APF-3000 pressure-sensitive adhesive reactive waterproofing membrane waterproofing membrane roofing when used in a single layer, the choice of mechanical fixation, full bonding method, an empty shop capping method. When the insulating layer is made of a fixed member is fixed, the coil should use mechanical fastening method of construction; when the grass is leveling cementitious material layer, fully adhered membrane should adopt the method of construction; waterproof membrane species according to the corresponding construction methods, should be Table 4.1-1 choice when using mechanical fixing methods laid, should be used in the enhanced (P type). Four, 1.2mmAPF-3000 pressure-sensitive adhesive reactive waterproofing of underground works 1) In addition to the main structure of underground works waterproof outer, when the water level of grade level, two channel waterproof layer fortification (APF-3000 waterproofing membrane -SA-Y P type pre-coated sheets for waterproofing excluded); when the water level is two, the single channel fortification. The minimum thickness of every 5 waterproof layer waterproof material selection, see table. 2) TPO waterproofing membrane lap width of 70mm / 80mm (self-adhesive / cementation zone). Stones bilayer membrane, two floors and an adjacent two coil should be staggered seams 1/3 ~ 1/2 width, and the two may not be mutually perpendicular paving the web. 3) waterproofing membrane adhesive quality requirements should be consistent with GB 50108-2008 "underground waterproof technical specifications" table 4.3.10 requirements. 4) kitchen and toilet, floor waterproofing 5) The kitchen floor drainage slope of not less than 1%, without water phenomenon. 6) waterproof wall between kitchen and a height of not less than 1800mm. Fifth, the production base of buffalo were workers Zhang Publisher